Manfrotto 175 clip clamp, female baby pin

Less Information.

The Gag is the combination of two sets of Grip Head Plates on one shaft, and with one locking spin handle. It serves many purposes, such as making a yoke with a Grip Head at each end or converting a Double Extension Arm to a Triple Extension Arm, feathering two Open End Scrims for a graduated lighting effect.

Less Information.

Strengthened to withstand greater clamping pressure than any other clamp of its kind, the Super Mafer Clamp is now even more diversely effective. The protective pads in the jaws have been reformulated for better gripping action. Because of its superior strength, several new attachments have been added. Comes standard with a 5/8" baby Pin.

Less Information.

The Double Super Mafer allows the use of two Mafer attachments with one clamp. The castings and the reformulated protective pads in the jaws are now strong enough for us to be able to make this Double Super Mafer Clamp. Use a Hollywood Superflex Arm at one end and a 5/8' Baby Pin with a light fixture at the other end, or do the reverse and use the small light fixture on the Superflex Arm and a Grip Head with Gobo Arm and Flag on the other end. The possibilities are endless!

Less Information.

Provides strong, solid gripping of round, square, or rectangular tubing and many other common and irregular shapes. Features ergonomic handle design and reinforced jaws, and the shaft is 1010 chrome plated steel. The Center Jaw has a fixed jaw mounted at the base of the Baby Pin portion of the shaft providing strong support for the pin.

Less Information.

Provides strong, solid gripping of round, square, or rectangular tubing and many other common and irregular shapes. Features ergonomic handle design and reinforced jaws, and the shaft is 1010 chrome plated steel. The End Jaw has the fixed jaw mounted at the end of the threaded portion of the shaft.

Less Information.

Extends grip of a Matthellini Clamp by 10". Must be used with a Matthellini clamp.

Less Information.

Less Information.

The Chain Grip provides maximum gripping power on any size pipe up to 6" in diameter. EXTREME CAUTION must be taken when the 5/8" pin provided on the adjustment screw is used. Be sure that any off-center weight is toward the locking direction (clockwise); allowing more weight on the other side could loosen the jaws.

Less Information.

Ideal for holding beadboard and foamcore bounce materials.

Less Information.

The Matthews Gaffer Grip with 5/8" Pins is a multi-use clamp which can hold small light fixtures virtually anywhere that the adjustable jaw can clamp over. The jaw is equipped with 12 rubber gripper pads that not only protect the surface being clamped but also provide greater gripping ability.

Less Information.

Made to clamp securely on overhead grids, car rigs, or camera car rails for mounting light fixtures. The Baby Grid Clamp can also be inverted with the pin mounting into a Grip Head for spanning pipe between two stands. Clamp will grip a pipe having a minimum diameter of 1-1/4" (1.660) OD and a maximum diameter of 1-1/2" (1.990) OD. Exceeds Tensile Strength @ 16,000 lbs.

Less Information.

Both the Baby Pipe Clamp and the Junior Pipe Clamp have a uniquely designed hook molded into the clamp which keeps the clamp on the pipe even with a light fixture attached while the bolt is being tightened. The Baby Pipe Clamp terminates in a 5/8 Pin with a safety chain and cotter pin attached.

Less Information.

Made to attach to the dropped ceiling tile support rails found in many offices, it affords the mounting of small lighting instruments on its 5/8" pin without the need for a stand. The Drop Ceiling Cable Holder (included with clip) clips onto the 5/8" pin to keep cables near the ceiling and out of the shot.

Less Information.

Another emergency kit gadget that allows the placement of a 5/8' pin in many unusual locations. Because of its strength and its very thin profile the Putty Knife can be slipped behind a door molding, windowsill molding, the top of a closed door, a baseboard, the backing on a bookcase, and so on, and so on, and so on.

Less Information.

ATTA PIN ensures that your heavy flags, cutters and scrims will stay exactly in place for as long as you need. Slip the ATTA PIN over the frame of the rag and connect the post to a mounted grip head for an accurate, rock-steady placement. May also be used to steady a knife blade gel frame.

Less Information.

Less Information.

Drop Downs are most commonly used on Lighting Booms. The pivoting mounting allows the use of a light box or other lighting instruments to maintain a horizontal position regardless of the angle of the boom.

Less Information.

Adapts from (1) Female Baby pin Receiver to (2) 5/8" Baby Pins.

Less Information.

Less Information.